Home / Lamps and Tealights / Funny Parrot Head Wall Lamp Laser Cut File

PetalSmith3D 1,330 files

Funny Parrot Head Wall Lamp Laser Cut File

Layered wood file

Be the first to review

Original price was: $8.00.Current price is: $5.60.

Funny Parrot Head Wall Lamp Laser Cut File, 3D Wooden Animal Head SVG DXF, Tropical Bird Sconce, LED Living Room Decor 3mm

Add the commercial licence — $5.00 Sell what you make from this file · What is included
  • Download straight after checkout
  • Test-cut before listing
  • Something wrong? We fix the file, free
Meet the designer
PetalSmith3D 1,330 files on MixiArt
Visit shop Message
Layerednumbered in stacking order
SVG, DXF, AI, PDFone file per layer
Alignment built inpin holes every layer
Numbered partsengraved on the back
Any sizeresized on request, free
Licence includedpersonal use
About this file

Funny Parrot Head Wall Lamp: a 3D laser cut kit of a cartoon parrot head on an oval wall plate, with big round eyes, an open ribbed beak, a crooked grin and a crest of long feathers. A 5 V USB LED puck sits in a drawer that slides in from the back, and the light shines out through the beak, the mouth and the gaps between the feathers.

THIS IS A DIGITAL FILE. No physical item will be shipped.

  • WHAT YOU GET
  • – Laser cut files in DXF and SVG, CUT (red) and ENGRAVE (blue, feather rows, eye lids, tongue) on separate layers, sheet border on its own layer (do not cut)
  • – Two versions: NOMINAL and KERF-COMP 0.15 mm
  • – Sheet layout previews (PNG)
  • FINISHED SIZE
  • – 261 mm wide, 311 mm tall, 350 mm from the wall to the beak tip (10.3 x 12.2 x 13.8 in), wall plate 227 x 242 mm
  • – 64 pieces (50 plates and 14 square pins 3 x 3 mm cut from the same board), slot and pin assembly, about 550 g (1.2 lb)
  • MATERIAL
  • – 3 mm plywood. The slots are 3.02 mm: measure your board, boards thicker than 3.05 mm (many 1/8 in boards are 3.175 mm) will be too tight.
  • – 5 sheets of 400 x 300 mm (15.75 x 11.8 in).
  • LASER MACHINE
  • – Working area needed: at least 390 x 290 mm (15.4 x 11.4 in). The largest piece is 365 x 193 mm.
  • – Fits: xTool S1 (498 x 319 mm), xTool P2 / P2S (600 x 308 mm), about 400 x 400 mm open-frame diode lasers (xTool D1 Pro, Atomstack A5 / A10, Sculpfun S30, Ortur LM3, Creality Falcon2), CO2 4040 (400 x 400 mm), CO2 6040 (600 x 400 mm) and larger.
  • – Fits after re-arranging the pieces: xTool M1 (385 x 300 mm), Glowforge Basic / Plus / Pro (495 x 279 mm).
  • – Too small: K40 (about 300 x 200 mm), 300 x 300 mm machines.
  • – Do not scale the files: the slots are made for 3 mm wood.
  • LIGHT (not included)
  • – 5 V USB LED disc (puck or COB module), 40 mm diameter x 10 mm, up to 1.5 W, warm white, cable up to 3 mm. It sits on a drawer that slides in through the wall plate from the back, and the cable runs down a channel in the back plate.
  • HARDWARE (not included)
  • – 2 wood screws 3.5 x 30 mm (pan head up to 9 mm diameter and 2.6 mm high) with wall plugs, level and 184 mm apart, for the two keyholes. Optional third countersunk safety screw near the bottom of the plate.
  • – Wood glue for the two eye tabs (recommended).
  • NOTES
  • – Plates with engraving on their visible face are drawn mirrored: engrave and cut them as drawn, then turn them over.
  • – Cut a few test pieces first (a neck ring with the chin keel, a keel with its feather, a piece of face plate) and check the slot fit with your board.
  • – The crest feathers are up to 194 mm long: lift the cut pieces out carefully.
What is in the download
  • PT61 laser cut files
Licence

Make it as many times as you like for yourself or as gifts. To sell finished pieces, add the commercial licence when you buy. The file itself may never be resold or shared.

Cut it with

Same material, same afternoon.

View all

From people who cut it

Reviews

There are no reviews yet.

Be the first to review “Funny Parrot Head Wall Lamp Laser Cut File”

Your email address will not be published. Required fields are marked *

Why these files cut cleanly

Cut before it is sold

Every file goes on a real machine and gets built by hand before it goes online. If it does not fit together, it does not go up.

Layers numbered on the back

Each part carries its layer number engraved on the reverse, so a stack of forty pieces never turns into a guessing game.

Alignment built in

Two 4 mm pin holes run through every wood layer. Glass patterns come with registration marks that survive printing.

Resized for free

Tell us the finished width you need and we redraw the file to match. No extra charge, usually back the same day.

Questions makers ask

What software do I need to open these?

LightBurn, xTool Creative Space, Glowforge and LaserGRBL all read the SVG straight off. The DXF is there for older machine software, and the AI and CDR files are for anyone who wants to edit the drawing.

My machine bed is smaller than the finished piece. Now what?

Every file also ships with each layer as its own file, so you can cut them one at a time on a small bed. Tell us your bed size and we will nest the parts to fit it.

Can I use wood that is not 3 mm?

Yes for the flat layered pieces — thicker wood just makes a deeper stack. For slot-together builds like the tealight shades the thickness is structural, so ask us and we will adjust the joints.

Do the glass patterns come sized for copper foil or lead came?

Both. Each pattern has two versions: a foil version with hairline cut lines, and a came version with the heart width already allowed for.

Can I sell what I make from these?

Personal use is covered by the free licence. Selling finished pieces needs the commercial licence, which is a few dollars on any file and included in every collection.

What if the file does not work on my machine?

Write to us with the file name and what happened. We fix the file and send it back. We do not reply with a link to a tutorial.