Home / Lamps and Tealights / Moose Lamp Laser Cut File

PetalSmith3D 1,330 files

Moose Lamp Laser Cut File

Layered wood file

Be the first to review

Original price was: $8.00.Current price is: $5.60.

Moose Lamp Laser Cut File, 3D Wooden Puzzle SVG DXF, Slatted Animal Night Light with Antlers, Cabin Lodge Decor 3mm to 6mm

Add the commercial licence — $5.00 Sell what you make from this file · What is included
  • Download straight after checkout
  • Test-cut before listing
  • Something wrong? We fix the file, free
Meet the designer
PetalSmith3D 1,330 files on MixiArt
Visit shop Message
Layerednumbered in stacking order
SVG, DXF, AI, PDFone file per layer
Alignment built inpin holes every layer
Numbered partsengraved on the back
Any sizeresized on request, free
Licence includedpersonal use
About this file

Moose Lamp: a 3D laser cut kit of a standing moose with wide antlers, ears, a dewlap and a short tail. Crosswise ribs on a centre spine form the slatted head and body, each leg is two layers, and a small LED bulb sits on a tray inside the head.

THIS IS A DIGITAL FILE. No physical item will be shipped.

  • WHAT YOU GET
  • – Laser cut files in DXF and SVG for 7 board thicknesses: 3 mm, 1/8 in (3.175 mm), 0.166 in (4.216 mm), 4 mm, 5 mm, 6 mm and 1/4 in (6.35 mm)
  • – CUT layer (red) and sheet border on its own layer (do not cut), no engraving
  • – Two versions for each thickness: NOMINAL and KERF-COMP 0.15 mm
  • – Sheet layout previews (PNG)
  • FINISHED SIZE
  • – 375 mm long, 275 mm wide at the antlers, 350 mm tall (14.8 x 10.8 x 13.8 in), the same at every thickness
  • – 51 pieces, glue-free slot assembly, about 240 g (0.5 lb) in 3 mm plywood
  • MATERIAL
  • – Plywood from 3 to 6.35 mm, one folder per thickness. The slots are the board thickness + 0.02 mm (3.02 mm in the 3 mm files): measure your board and use the folder that matches. Many 1/8 in boards are 3.175 mm and will be too tight in the 3 mm files.
  • – 5 sheets of 400 x 300 mm (15.75 x 11.8 in) at every thickness.
  • LASER MACHINE
  • – Working area needed: at least 390 x 290 mm (15.4 x 11.4 in). The largest piece is 375 x 171 mm (the spine).
  • – Fits: xTool S1 (498 x 319 mm), xTool P2 / P2S (600 x 308 mm), about 400 x 400 mm open-frame diode lasers (xTool D1 Pro, Atomstack A5 / A10, Sculpfun S30, Ortur LM3, Creality Falcon2), CO2 4040 (400 x 400 mm), CO2 6040 (600 x 400 mm) and larger.
  • – Fits after re-arranging the pieces: xTool M1 (385 x 300 mm), Glowforge Basic / Plus / Pro (495 x 279 mm).
  • – Too small: K40 (about 300 x 200 mm), 300 x 300 mm machines.
  • – Do not scale the files: the slots are made for the board thickness of each folder.
  • LIGHT (not included)
  • – Small round LED bulb up to 28 mm diameter and 30 mm tall (27 mm with 6 mm boards and thicker), its socket through the 10 mm hole in the lamp tray. LED only. The body is hollow, so an LED string fits inside too.
  • – The cable runs along the spine into the body and down between the two layers of the right hind leg, out at the heel. To reach the bulb, lift the antler rib and the head ribs in front of it.
  • NOTES
  • – Cut one body rib and a piece of the spine first and check the slot fit with your board. The hoof pads and the lamp tray are held by friction: if the NOMINAL file is loose, use KERF-COMP.
  • – Fit the lamp tray before the antler rib. With 5 mm boards and thicker, drop head rib H03 after the lamp tray.
What is in the download
  • PT60 laser cut files
Licence

Make it as many times as you like for yourself or as gifts. To sell finished pieces, add the commercial licence when you buy. The file itself may never be resold or shared.

Cut it with

Same material, same afternoon.

View all

From people who cut it

Reviews

There are no reviews yet.

Be the first to review “Moose Lamp Laser Cut File”

Your email address will not be published. Required fields are marked *

Why these files cut cleanly

Cut before it is sold

Every file goes on a real machine and gets built by hand before it goes online. If it does not fit together, it does not go up.

Layers numbered on the back

Each part carries its layer number engraved on the reverse, so a stack of forty pieces never turns into a guessing game.

Alignment built in

Two 4 mm pin holes run through every wood layer. Glass patterns come with registration marks that survive printing.

Resized for free

Tell us the finished width you need and we redraw the file to match. No extra charge, usually back the same day.

Questions makers ask

What software do I need to open these?

LightBurn, xTool Creative Space, Glowforge and LaserGRBL all read the SVG straight off. The DXF is there for older machine software, and the AI and CDR files are for anyone who wants to edit the drawing.

My machine bed is smaller than the finished piece. Now what?

Every file also ships with each layer as its own file, so you can cut them one at a time on a small bed. Tell us your bed size and we will nest the parts to fit it.

Can I use wood that is not 3 mm?

Yes for the flat layered pieces — thicker wood just makes a deeper stack. For slot-together builds like the tealight shades the thickness is structural, so ask us and we will adjust the joints.

Do the glass patterns come sized for copper foil or lead came?

Both. Each pattern has two versions: a foil version with hairline cut lines, and a came version with the heart width already allowed for.

Can I sell what I make from these?

Personal use is covered by the free licence. Selling finished pieces needs the commercial licence, which is a few dollars on any file and included in every collection.

What if the file does not work on my machine?

Write to us with the file name and what happened. We fix the file and send it back. We do not reply with a link to a tutorial.